Maytag Bravos Washer How to Read Diagnostic Test
Maytag Bravos Diagnostic Modes
Caution! Diagnostic modes are preformed with the washing machine plugged in and will also featherbed some of the washing machines standard safe features. Farthermost caution should exist used to avoid electric stupor as well as injury or expiry due to moving parts!
Note: The washer should perform as described in these tests. Still, the information contained in your washer'southward wire diagram and technical sheet may be slightly dissimilar. Always double-check your washing motorcar's wire diagram and technical canvass before cartoon a conclusion. If you get a different result yous may want to look at the component descriptions on this page for more clues and tests.
Troubleshooting Mutual Problems | Tips & Tricks
Automatic Diagnostic Test Fashion:
1. The washing machine needs to be plugged in and in stand by mode with all indicators off.
2. Choose whatsoever one push on the washer'south console except Power, Beginning, or Stop. Press/Hold three Seconds - Release 3 Seconds - Printing/Agree 3 Seconds - Release 3 Seconds - Press/Agree three Seconds.
iii. If the diagnostic examination manner has been successfully entered, all of the indicator lights will glow for five seconds with 88 on the time display. (If information technology didn't piece of work try #two once again One one thousand…Two ane thousand…3 one thousand)
4. If in that location are any saved error codes they will be displayed. If there are no save fault codes all indicator lights will plough off for a moment then dorsum on with 88 displayed and the automated diagnostic exam mode volition begin in 5 seconds.
5. If you are unable to enter the diagnostic test mode, press the power button and verify that the button you were trying to utilise operates properly to program the washer's cycle office. In that location may be something wrong with that role push button. Notice another button on the control that appears to work and attempt to enter the diagnostic mode with that button. You may also want to verify that the user interface has a good connection to the washing car control board at the P11 concluding.
Back to Top
Note: Pressing the Finish or Ability button at whatsoever fourth dimension to exit the washing machine's diagnostic mode.
| Two-Digit | Machine Operation | Side by side Stride |
| C0 | Slow spin to 23 rpm | If the tub does not spin go to Bravos transmission diagnostic mode: Motor, Spin. |
| C1 | Hot and cold (Warm Water) primary water valves open as well as the detergent and fresh fill valves, then the fresh valve until the handbasket floats, disengaging from the basket hub. The washer will so continue filling through the detergent and fresh valves to the minimum h2o level. | If there is no h2o or the water temperature is wrong go to Bravos manual diagnostic mode: H2o valves. |
| C2 | The cold water valve and the bleach valve open for 10 seconds. | If no water flows through the bleach loving cup go to Bravos manual diagnostic mode: H2o valves. |
| C3 | Hot water and fabric softener valves are opened for 10 seconds. Note: if yous washing machine doesn't have a textile softener dispenser, this step will happen but no water volition flow. | If your washing automobile has a material softener dispenser and no water flows go to Bravos mannual diagnostic mode: Water valves. |
| C4 | Hot and common cold (Warm Water) principal water valves open up as well as the detergent water valve for 10 seconds | If no h2o flows through the detergent loving cup go to Bravos transmission diagnostic style: Water valves |
| C5 | The washing machine volition agitate for 15 seconds. | If the washing machine does not agitate go to Bravos manual diagnostic mode: motor, agitate. |
| C6 | The washing motorcar's recirculation pump will energize for 10 seconds | If no h2o is being re-circulated go to Bravos manual diagnostic mode: Pumps. |
| C7 | The washing machine's drain pump is energized until the inner wash handbasket reengages with the basket hub plus an extra 10 seconds timed bleed. | If h2o is not draining from the washing machine become to Bravos manual diagnostic way: Pumps |
| C8 | The washer will keep to drain and slow spin at 23 rpm | If the drain pump is non pumping water from the tub go to Bravos manual diagnostic mode: Pumps. |
| C9 | The inner wash basket should coast to a stop. | If the basket does not terminate spinning inside 5 seconds press the end button on the washer's control and restart the examination. |
| (None) | Bike Point Beeps. | If no beep is heard verify that the wheel point is on. |
Back to Top
Manual Diagnostic Test Style
Perform steps 1 and 2 for the activation of the Bravos automatic diagnostic exam mode then printing the same button one more than time while 88 is on the washing machine brandish for 5 seconds. Pressing the "STOP" or "Ability" push at whatsoever time to exit the washing machine's diagnostic mode.
Notation: If the button is not pressed within the v seconds that the 88 is displayed the automatic diagnostic exam style volition begin after any saved fault/ error codes are displayed.
If the transmission diagnostic test manner was entered correctly you will hear a single beep and a 2 digit console ID# is displayed for 3 seconds followed by 00 and the "add a garment" indicator light will wink.
If no 2 digit panel ID# code is displayed you may need to supersede the user interface, but try to run the rest of the test anyway.
Note: If no buttons are pressed on the washing auto within 5 minutes the washer will go out the transmission diagnostic test mode and enter the normal standby style.
Water Level Sensor Calibration
Pressing and property the "Cycle Signal" button until a single beep is heard and the brandish displays "Pt" for naught scale can recalibrate the water level sensor. (All clothing and water must be out of the washing motorcar's tub for proper calibration.
Water Valves
Important Note: When manually opening the water valves in the diagnostic mode the h2o valves WILL NOT automatically be turned off by the pressure-sensing switch. Don't go make a sandwich with water flowing into the washing machine's tub or your firm will become a swimming puddle!
Past turning the bicycle selection knob or selecting a particular bicycle setting (push button models) and then pressing the "Outset" button you tin manually energize a secondary dispenser valve to test if information technology is working properly. Pressing the "Start" button a second fourth dimension will plough the valve off.
Pressing the "Wash/Rinse Temp" Selection push will energize the primary hot and common cold h2o valves. The appropriate water valve volition open for your selection.
Hot + Kickoff = Opens the hot valve
Cold + Start = Opens thecold valve
Warm + Start = Opens the both hot and cold valves.
Note: For h2o to enter the tub at to the lowest degree i a primary and one secondary valve must exist opened. Just the Fresh, Detergent, Bleach, or Material softener valve solenoids past themselves will not release water into the washer tub.
Back to Summit
| Pressing the "Start" push volition turn the valve on and off | |
| Select Bike With Knob or Push | Valve Solenoid Energized |
| Whites/Whites + Start | Fresh Make full |
| Heavy Duty + Starting time | Detergent |
| Normal + Showtime | Textile Softener (not all models) |
| Casual + Start | Bleach |
Recirculation & Drain Pump Tests:
Note: Pumps move water… so these tests piece of work all-time if you take filled the washing machine tub with some h2o with the water valve tests above.
To manually activate the Recirculation pump on the Maytag Bravos Washing Machines press and release the "Clean Washer" or "Bleed & Spin" button (push button models) or Select the "Make clean Washer" or "Bleed & Spin" cycle option and press start (rotary knob models).
Pressing the "Make clean Washer", "Drain & Spin", or "Start" push a second time will plough the recirculation pump off. Pressing the "Clean Washer", "Drain & Spin", or "Start Push button" again will turn on the drain pump. Pressing the "Make clean Washer", "Drain & Spin", or "Start Button" push button a 4th time will turn the drain pump off.
Lid Switch Examination:
Opening the washing auto lid should cause the "Clothes Clean" or "Washed" indicator lights to turn off. Closing the hat should cause the "Clothes Clean" or "Done" indicator lights to turn on.
Lid Lock Examination:
Note: Lid must be closed when doing this exam or an invalid push button noise will be heard.
To Lock the hat printing and release the "2d Rinse" or "Extra Rinse" push button, the door lock calorie-free will come on. To unlock the lid printing the "2d Rinse" or "Actress Rinse" button a second fourth dimension, the door lock light will plough off.
Motor Tests:
Note: Water should be covering the launder plate or agitator vanes to allow the inner basket to float and disengage from the basket hub for all motor tests. See Manual Water Valve Diagnostic Tests. Issues with any of the motor tests are most oft related to something lodged between the inner and outer wash baskets creating friction, bad wire connections, cleaved wires, or control problems.
Rotor Position Sensor (RPS):
The three rinse and spin indicators are used to observe the 3 rotor position sensors located on the washing machine'southward motor stator. As the inner launder basket rotates so does the rotor. Lift the chapeau and manually rotate the inner tub as the tub turns these three lights should wheel on and off indicating that the RPS is correctly detecting the position and speed of the rotor.
Spin:
Note: to activate the spin the lid must be closed and the lid lock engaged. See Chapeau Switch Tests. If the lid is not airtight or locked an invalid fundamental beep will sound. Likewise the tub must be floating for this test to work properly.
To start the washing machine spinning at 23 rpm printing the "Spin Speed", "H2o Level", or "Load Size buttons. Press the same button again to accelerate to 530 rpm. Press the same button once again to accelerate to one thousand rpm. Pressing the aforementioned button a fourth time will turn off the motor. You will too find the RPS sensing lights are active during all washer motor tests.
Agitate:
To manually beginning the washing machine's agitation printing and release the "Soil Level" button in one case for the gentle wash activeness, a 2d time for the normal activity, a 3rd time for the Heavy wash action, and a 4th time to turn the motor off.
Console & Indicator Diagnostic Test Mode
The Console and indicator diagnostic test on a Maytag Bravos Washing Motorcar is used to check the cycle selector knob, console indicators, user interface buttons, two-digit brandish, and beeper.
1. The washing machine should exist in standby (off) mode.
2. Press and release the following buttons within iv seconds.
"Soil Level" – "Wash/Rinse Temp" - "Soil Level" - "Wash/Rinse Temp"
3. if successful "dt" should display on the washing machines indicator.
iv. Whithin 5 seconds press "Starting time" all indicator lights should come on and 88 should be displayed.
five. Press start once more to turn off the status indicators and the two-digit display, all other indicators should remain lit.
6. Press "Start" over again to turn all indicator lights back on. Rotating the wheel selector knob back and forth should turn the corresponding lights off or on. Pressing buttons should as well toggle lights on and off to verify they are working properly. Pressing the "Soil Level", "Spin Speed:, "Water Level", "Load Size", or "Wash/Rinse Temp" buttons should lite upwards all indicators for that selection.
Back to Top
Maytag Bravos Error Codes
Source: https://applianceassistant.com/Washer-Repair/Maytag-Bravos/Maytag-Bravos-Washer-Diagnostic-Modes.php
Post a Comment for "Maytag Bravos Washer How to Read Diagnostic Test"